There are few common cases we've seen where k0s fails to run properly.
CoreDNS in crashloop#
The most common case we've encountered so far has been CoreDNS getting into crashloop on the node(s).
With kubectl you see something like this:
$ kubectl get pod --all-namespaces NAMESPACE NAME READY STATUS RESTARTS AGE kube-system calico-kube-controllers-5f6546844f-25px6 1/1 Running 0 167m kube-system calico-node-fwjx5 1/1 Running 0 164m kube-system calico-node-t4tx5 1/1 Running 0 164m kube-system calico-node-whwsg 1/1 Running 0 164m kube-system coredns-5c98d7d4d8-tfs4q 1/1 Error 17 167m kube-system konnectivity-agent-9jkfd 1/1 Running 0 164m kube-system konnectivity-agent-bvhdb 1/1 Running 0 164m kube-system konnectivity-agent-r6mzj 1/1 Running 0 164m kube-system kube-proxy-kr2r9 1/1 Running 0 164m kube-system kube-proxy-tbljr 1/1 Running 0 164m kube-system kube-proxy-xbw7p 1/1 Running 0 164m kube-system metrics-server-7d4bcb75dd-pqkrs 1/1 Running 0 167m
When you check the logs, it'll show something like this:
kubectl -n kube-system logs coredns-5c98d7d4d8-tfs4q
plugin/loop: Loop (127.0.0.1:55953 -> :1053) detected for zone ".", see https://coredns.io/plugins/loop#troubleshooting. Query: "HINFO 4547991504243258144.3688648895315093531."
This is most often caused by systemd-resolved stub (or something similar) running locally and CoreDNS detects a possible loop with DNS queries.
The easiest but most crude way to workaround is to disable the systemd-resolved stub and revert the hosts
/etc/resolv.conf to original
Read more at CoreDNS troubleshooting docs.
k0s controller fails on ARM boxes#
In the logs you probably see etcd not starting up properly.
Etcd is not fully supported on ARM architecture, thus you need
k0s controller and thus also etcd process with env
As etcd is not fully supported on ARM, it also means that the k0s control plane with etcd itself is not fully supported on ARM either.
k0s will not start on ZFS-based systems#
On ZFS-based systems k0s will fail to start because containerd runs by default in overlayfs mode to manage image layers. This is not compatible with ZFS and requires a custom config of containerd. The following steps should get k0s working on ZFS-based systems:
- check with
$ ctr -a /run/k0s/containerd.sock plugins lsthat the containerd ZFS snapshotter plugin is in
okstate (should be the case if ZFS kernel modules and ZFS userspace utils are correctly configured):
TYPE ID PLATFORMS STATUS ... io.containerd.snapshotter.v1 zfs linux/amd64 ok ...
- create a containerd config according to the documentation:
$ containerd config default > /etc/k0s/containerd.toml
- modify the line in
... [plugins."io.containerd.grpc.v1.cri".containerd] snapshotter = "overlayfs" ...
... [plugins."io.containerd.grpc.v1.cri".containerd] snapshotter = "zfs" ...
- create a ZFS dataset to be used as snapshot storage at your desired location, e.g.
$ zfs create -o mountpoint=/var/lib/k0s/containerd/io.containerd.snapshotter.v1.zfs rpool/containerd
- install k0s as usual, e.g
$ k0s install controller --single -c /etc/k0s/k0s.yaml
- containerd should be launched with ZFS support and k0s should initialize the cluster correctly
Pods pending when using cloud providers#
Once we enable cloud provider support on kubelet on worker nodes, kubelet will automatically add a taint
node.cloudprovider.kubernetes.io/uninitialized for the node. This tain will prevent normal workloads to be scheduled on the node until the cloud provider controller actually runs second initialization on the node and removes the taint. This means that these nodes are not available for scheduling until the cloud provider controller is actually successfully running on the cluster.
For troubleshooting your specific cloud provider see its documentation.
k0s not working with read only
By default k0s does not run on nodes where
/usr is read only.
This can be fixed by changing the default path for
volumePluginDir in your k0s config. You will need to change to values, one for the kubelet itself, and one for Calico.
Here is a snippet of an example config with the default values changed:
spec: controllerManager: extraArgs: flex-volume-plugin-dir: "/etc/kubernetes/kubelet-plugins/volume/exec" network: calico: flexVolumeDriverPath: /etc/k0s/kubelet-plugins/volume/exec/nodeagent~uds workerProfiles: - name: coreos values: volumePluginDir: /etc/k0s/kubelet-plugins/volume/exec/
With this config you can start your controller as usual. Any workers will need to be started with
k0s worker --profile coreos [TOKEN]
We drop any debug related information and symbols from the compiled binary by utilzing
-w -s linker flags.
To keep those symbols use
DEBUG env variable:
DEBUG=true make k0s
Any value not equal to the "false" would work.
To add custom linker flags use
LD_FLAGS="--custom-flag=value" make k0s
I'm using custom CRI and missing some labels in Prometheus metrics#
Due to removal of the embedded dockershim from Kubelet, the Kubelet's embedded
cAdvisor metrics got slightly broken. If your container runtime is a custom
containerd you can add
--kubelet-extra-flags="--containerd=<path/to/containerd.sock>" into k0s worker
startup. That configures the Kubelet embedded cAdvisor to talk directly with
containerd to gather the metrics and thus gets the expected labels in place.
Unfortunately this does not work on when using Docker via cri-dockerd shim. Currently, there is no easy solution to this problem.
In the future Kubelet will be refactored to get the container metrics from CRI interface rather than from the runtime directly. This work is specified and followed up in KEP-2371 but until that work completes the only option is to run a standalone cAdvisor. The known issues section in the official Kubernetes documentation about migrating away from dockershim explains the current shortcomings and shows how to run cAdvisor as a standalone DaemonSet.
- All data directories reside under
/var/lib/k0s, for example: